搜索结果: 1-15 共查到“curing”相关记录56条 . 查询时间(0.128 秒)
Mechanical properties of carbon nanotubes/epoxy nanocomposites: Pre-curing, curing temperature, and cooling rate
Carbon nanotubes curing epoxy mechanical properties nanocomposites polymer nanocomposites
2023/11/30
The effects of composite fabrication, such as pre-curing, curing temperature, and cooling rate, were studied. In this work, the pre-curing was defined as heat treatment of Multi-Walled Carbon Nanotube...
Low-temperature 3D printing and curing process of continuous fiber-reinforced thermosetting polymer composites
3D printing CFRTPC curing behavior prediction low-temperature process model-free kinetics
2023/11/16
The reported work has developed a methodology of printing and curing continuous fiber-reinforced thermosetting polymer composites (CFRTPCs) with excellent mechanical properties at low temperatures. Fi...
Effect of Curing Time on the Physicochemical and Sensory Properties of Beef Jerky Replaced Salt with Soy Sauce, Red Pepper Paste and Soybean Paste
Soy Sauce Red Pepper Paste Soybean Paste
2016/5/17
This study was done to investigate the quality properties of beef jerky with soy sauce, red pepper paste, and soybean paste replacing salt. Sliced beef samples were cured in salt (control), soy sauce,...
Evaluation of Correlation between Within-Barn Curing Environment and TSNA Accumulation in Dark Air-Cured Tobacco
Within-Barn Curing Environment TSNA Accumulation
2014/6/3
Significant effect of number of hours above 80% relative
humidity on TSNA,Greater correlation between number of hours above 80%
relative humidity and TSNA at Lexington (407 hrs vs. 131 hrs at
Pr...
Removal of Unpleasant Odorous Substances from Smoke Produced by Smoke Curing Houses
Meat industry odorous thermal decomposition
2010/12/22
Problem statement: For purification of smoke in PPHU Duda-Bis Plant water washers, placed in the outlet channel of smoke chamber, have been applied, but the amount of the substances remaining in the a...
Influence of filling technique and curing mode on the bond strengths of composite cores to pulpal floor dentin
Composite resin core Filling technique Pulpal floor dentin
2010/11/30
This study evaluated the influence of filling technique and curing mode on the microtensile bond strengths (MTBS) of composite cores to pulpal floor dentin. Access cavities of human molars with pulpal...
A review of the development of radical photopolymerization initiators used for designing light-curing dental adhesives and resin composites
Radical photopolymerization Photoinitiator Light-curing dental adhesive
2010/11/30
This paper reviews our recent studies on radical photopolymerization initiators, which are used in the design of light-curing dental adhesives and resin composites, by collating information of related...
Microtensile bond strengths of a dual-cure resin cement to dentin resin-coated with an all-in-one adhesive system using two curing modes
Resin coating Resin cement All-in-one adhesive
2010/11/26
This study evaluated the effect of resin coating using an all-in-one adhesive system on the dentin bond strength of a dual-cure resin cement after different curing modes. Human molars were ground to o...
Effect of saliva contamination prior to curing on microleakage of pit and fissure sealants,an in vitro study
Microleakage Pit and fissure sealant Light curing Saliva contamination
2009/12/18
Background and Aim: Pit and fissure sealant therapy, is one of the most effective methods, in prevention of occlusal caries. Saliva contamination before curing the resin can increase the risk of failu...
Effectiveness of composite resin polymerization using light-emitting diodes (LEDs) or halogen-based light-curing units
Composite resins Spectrophotometry
2009/10/20
The clinical performance of composite resins is greatly influenced by the quality of the light-curing unit used. The aim of this study was to compare the efficiency of a commercial light-emitting diod...
The influence of chemical activation on hardness of dual-curing resin cements
Resin cements Hardness Dental materials
2009/10/20
During the cementation of metallic restorations, the polymerization of dual-curing resin cements depends exclusively on chemical activation. This study evaluated the influence of chemical activation c...
Effect of light curing tip distance and resin shade on microhardness of a hybrid resin composite
Composite resins Hardness
2009/10/20
Resin composite shades and resin composite polymerization performed with a distanced light tip are factors that can affect polymerization effectiveness. Thisin vitro study aimed to evaluate the influe...
Influence of activation modes on diametral tensile strength of dual-curing resin cements
Resin cements Tensile strength Dental materials
2009/10/20
In metallic restorations, the polymerization of dual-curing resin cements depends exclusively on chemical activation. The effect of the lack of photoactivation on the strength of these cements has bee...
Influence of composite restorative materials and light-curing units on diametrical tensile strength
Light emitting diode Composite resins Diametrical tensile strength Mechanical properties
2009/10/19
The aim of this study was to evaluate the diametrical tensile strength (DTS) of three light-curing photo-activated composites with two different light curing units (LCU). Three types of dental restora...
Hardness of a bleaching-shade resin composite polymerized with different light-curing sources
Composite resins Dental materials Hardness
2009/10/19
The microhardness of a bleaching-shade resin composite polymerized with different light-curing units was evaluated. Composite samples (3M ESPE Filtek Supreme) were applied to brass rings (2 mm in thic...